|
|
|
10-120 WIRELESS MICROPHONE RECEIVER This professional receiver is designed with the latest wireless technology. The low drop-out-free RF is excellent under adverse conditions. Audio performance is comparable to more expensive systems. It has "TRUE DIVERSITY" reception for excellent RF performance. |
|
| Specifications | |
|
Frequency Range....VHF 169-216 MHZ (10 channels) Working Range.....Up to 300' under average conditions Distortion.....Less than 1%(+/- 15khz dev.) Frequency Response.....40Hz-15khz (+/-3db) Dynamic Range.....Better than 100db Signal to noise ratio.....Better than 95db Noise reduction.....2:1 logarithmic compressor/expander Oscillator/modulator.....Crystal controlled/Fm |
Image rejection.....Better than 60db Reception Sensitivity.....Better than 15db uv Reception selectivity.....+/-60khz Audio output adjustment Min-30db,center Odb,max 6db Audio output impedance.....2.2Kohms unbalanced Power requirements.....12 Vdc-300ma Size.....(mm)280W x 120D x37H Weight.....290z. (830grams) |
|
10-121 MICROPHONE SYSTEM A VHF hi-band wireless microphone system. Comes complete with a handheld microphone. The receiver operates on a quartz-locked principal for a clear distortion-free signal. Operational frequency is 160-240Mhz. |
|
| Specifications | |
|
MICROPHONE Sensitivity.....10db SPL at 7Khz FM deviation Frequency response.....100Hz-12000Hz RF output power.....50mV(max) Power supply.....9 volt battery Power consumption.....30mA(average) Battery life.....8hours (average) |
RECEIVER Sensitivity.....10uV S/N ratio at 1mV output.....60db Output power (line) Output power (microphone).....16 +/- 4mV Total harmonic distortion.....1% typical Power requirement.....12 Vdc,200ma |
|
10-127 WIRELESS MICROPHONE SYSTEM This professional quality VHF microphone system has a range of over 250 feet. With two switchable frequencies for the cleanest sound at an affordable price. Has clip on microphone. Ideal for camcorder use. A monitor earphone is included. |
|
| Specifications | |
|
TRANSMITTER Frequencies.....169.445mHZ+170.245mHZ Sensitivity.....94db SPL at +/-2.5Khz deviation Power supply.....one 9 volt battery (not included) Power consumption.....30mA Dimensions.....86 x 60 x 21.5mm Weight.....170grams Microphone.....Electret condenser |
RECEIVER Reception system.....Double superhederodyne system Frequencies.....F1 169.445Mhz = F2 170.245Mhz Sensitivity.....2uV at S/N 40db Power supply.....one 9 volt battery(not included) Power consumption.....25mA Monitor output.....voltage:1v(load 30ohms) modfreq: 1khz Dimensions.....86 x 60 x 21.5 MM Weight.....128 grams (including battery) Accessories supplied.....Earphone |
|
10-130 WIRELESS MICROPHONE This is the same quality microphone used in the 10-126 system. It delivers a 200 foot range for use with videography and public speaking. Its clean crystal controlled output is equal to more expensive systems. |
|
| Specifications | |
|
Frequencies Sensitivity Power supply Power consumption Weight Microphone |
169.445Mhz + 170.245Mhz 94db SPL at +/- 2.5Khz deviation one 1.5v AA battery (not included) 30mA 170 grams Electret condenser |
|
10-131 WIRELESS TRANSMITTER This wireless transmitter has a clip on lapel microphone ideal for many uses. This microphone has a range of over 200 feet. It has two switchable frequencies for the clearest signal available. |
|
| Specifications | |
|
Frequencies Sensitivity Power supply Power consumption Dimensions Weight Microphone |
169.445Mhz + 170.245Mhz 94db SPL at +/- 2.5Khz deviation one 9 volt battery (not included) 30mA 86 x 60 x 21.5 mm 170 grams Electret condenser |
|
10-126 WIRELESS TRANSMITTER This handheld microphone is ideal for videographers and public speaking. The VHF system has two switchable frequencies for selecting the cleanest sound, and delivers a crystal clear sound range of more than 200 feet. The transmitter is built into the handle of the microphone with no wires extending out of the base. The receiver has a cord terminated by a 3.5mm plug. |
|
| Specifications | |
| TRANSMITTER | |
|
Frequencies Sensitivity Microphone Power supply Power consumption Weigh |
169.445MHz - 170.245MHZ 94db spl +- 2.5KHz dev unidirectional-dynamic one 1.5v AA battery (not included) 100mA 98 grams |
| RECEIVER | |
|
Frequencies Sensitivity Reception system Power supply Power consumption Weight |
169.445MHz - 170.245MHZ 2uV at S/N 40db double superheterodyne one 9v battery (not included) 25mA 128g (including battery) |
|
10-17 SHOTGUN MICROPHONE This is a high quality sound !ocating shotgun microphone. It is equipped with a high quality internal amplifier and earbud type earphones. Can be easily mounted on camcorders, binoculars, or hand-held. It has an adjustable volume control for clear output. The supercardioid pattern is designed for medium range frequencies to isolate and pickup human voices at directional short distances. |
|
| Specifications | |
|
Microphone Pattern Output Level Acoustic Gain Frequency Response Power Source Battery Life Weight Earphones Measurements Color Accessories |
Electric condenser Unidirectional Supercardioid 5m watts MA at earphone 50db 200-15KHZ 1 AAA Battery 100 hours (continous operation) 65 grams (incl. battery & earphones) Inner-ear Type Stereo -32 ohms 238 (L) X 30 (H) X 17 (W) Black Earbud Headphones, Mounting Hardware. and Directional Tube, Thread Adapter |
|
10-13 SUPER CARDIOID SHOTGUN MIC Two complete mikes in one-Super Cardioid for long range pickup. Unscrew and adapt a Uni directional for normal use. Each microphone is a Condenser Type. Back Electret Technique with l.C. Preamplification. Impedance - 600 ohm complete with Wind Screens, Case and Microphone Holder. |
|
| Specifications | |
| SUPER CARDIOID | |
|
Type Frequency Response Sensitivity Impedance Directional Polar Response Input Equiv. Noise Level Max. Sound Pressure Level Min. Actual Load Impedance Power Supply Battery Working Life Battery Power Consumption Connector Cable End Case Microphone Holder Dimension Weight |
Condenser 50 Hz-15, 000 Hz .-55 dB +/- 3 dB 600 ohms +/- 25% Super Cardioid 22 dB SPL 22 db SPL 3K ohms Size "AA" Penlite Cell (1.5v) Standard Type 3000H--Alkaline Type: 5000H 400 uA +/- 20% XLR-3 Type 1/4" Phone plug Aluminum Body with Steel Mesh Grill Slip-in type with Standard 5/ 8" 27 Thread 20 0 x 385 mm 250 gr |
| UNIDIRECTIONAL | |
|
Type Frequency Response Sensitivity Impedance Directional Polar Response Input Equiv. Noise Level Max. Sound Pressure Level Min. Actual Load Impedance Power Supply Battery Working Life Battery Power Consumption Connector Cable End Case Microphone Holder Dimension Weight |
Microphone in Back Electret Technique with IC-Preamplifier 30 Hz-20,000 Hz -68 dB +/- 2.5 dB 600 ohms +/- 25% Uni-directional Cardioid 30 dB SPL 128 dB SPL 3K ohms Size "AA" Penlite Cell (1.5v) Standard Type 3000H--Alkaline Type: 5000H 400 uA +/- 20% XLR-3 Type 1/4" Phone plug Aluminum Body with Steel Mesh Grill Slip-in type with Standard 5/ 8" 27 Thread 28 0 x l 95 mm 95 gr |
|
10-10 SUPER CARDIOID SHOTGUN MIC Super directive use. Can pick up objective sound clearly-even in noisy environments. Shakeproof holder acts as a vibration damping mechanism and helps eliminate unwanted mechanical and motor noises. Impedance 600 Ohm 11 kHz) Complete with Case and Wind Screen. 3.5 mm plug. |
|
| Specifications | |
|
Type Directivity Sensitivity Output Impedance Frequency Range Std. Working Voltage Current Drain S/N Ratio |
Electret Condenser Microphone Super Directional 60 dB (1 kHz 0 dB = 1V/u Bar) 600 ohms 1(kHz) 50 Hz-10 kHz 1.5V (DC) 1 mA Max 40 dB or more (1 kHz JISA-curve) |
|
10-15 SUPER CARDIOID SHOTGUN MIC This microphone is for Super-Directive use with high sensitivity and extremely low noise. It can pick up clearly and naturally the object's sound even in noisy environment of both short and long distance. The 10-15 microphone is designed primarily For operational efficiency and well suited to outdoor sports broadcast stage video and movies Can be hand held, stand mounted or mounted on video or movie equipment. |
|
| Specifications | |
|
Type System Sensitivity: Frequency Response: 0utput Impedance Power Source Sound Pressure Level Signal to Noise Ratio Cable Accessories |
Super Cardioid Electret Condenser Uni-directional system for long and short distance (Switchable) For short distance: -66 dB (1 V/u bar 1 kHz) For long distance: -56 dB (1 V/u bar 1 kHz) 80 Hz-12,000 Hz For short distance: 520 ohms DC 1.5V, AA Size Battery (not included) 120 dB Max 40 dB or More coiled with 3.5 mm plug Wind Screen and Mike Holder |
|
10-18B PROFESSIONAL DYNAMIC MICROPHONE Outstanding quality balanced line extra wide range uni-directional cardioid pattern designed to meet the most demanding types of use such as rock groups recording sessions entertainers and public address work. Distinctively finished in satin anodize. Complete with wind screen, stand holder. |
|
| Specifications | |
|
Element Frequency Response Polar Pattern 0utput Level 0utput impedance Cable Cable end |
Dynamic 80-16,000 Hz Uni-directional -74 dB at 1 Microbar Low Z 15 ft. Balanced line 1/4" Phone plug |
|
10-16 PROFESSIONAL DYNAMIC MICROPHONE Superior sound quality extremely wide range. Cardioid pattern used by many entertainers for vocal and recording work, lightweight yet rugged for most everyday types of microphone needs. Complete with on/off/standby switching, stand holder. |
|
| Specifications | |
|
Frequency Response Power Supply Amplifier Polar Pattern 0utput Level (1,000 Hz) Generating Element 0utput Impedance S/N Ratio Equivalent Noise Current Consumption Battery Life Cable Cable end |
40-16,000 Hz Internal 1.5V Battery Size AA(included) (IC Impedance Converter) Cardioid -68 18 + 2 dB Electret Condenser 600 ohm Greater than 44 dB Level Less than 30 dB SPL 200 uA + 50 uA 5, 000 hrs. in continuous operation 15 ft. Balanced Line 1/4" Phone plug |
|
10-6A, 1 0-7A ELECTRET CONDENSER MICROPHONES Specially designed to meet most everyday microphone needs. High quality low cost lightweight small in size. Can be hand held or stand mounted. Complete with on/off switch, wind-screen and mic holder. |
|
| Specifications | |
|
0utput Level Frequency Response Polar Pattern Impedance Power Supply Current Consumption Cable Amplifier Cable end |
+3dB at 1 hHz(10-6A) +3dB at 1 kHz(10-7A) 50- 14 000 ( 1 0-6A) 50-13 000 (10-7A) Uni-directional (10-6A) Omni-directional ( 1 0-7A) 600 ohms (10-6A)AA Type 1.5 Battery (Included) 250 uA + 50 uA15 ft. 2-Conductor Shielded FET Impedance Converter Both hove 1/4" Phone plug |
|
10-1, 10-2 HANDS-FREE MICROPHONES This slim and lightweight microphone is worn on the head for hands-free operation. Perfect for on stage use with vocal or voice only. The soft lightweight headband makes this microphone perfect for long term use. The 10-1 s unidirectional electret condenser microphone gives a clear quality sound that eliminates most background noise. The 10-2 s unidirectional dynamic microphone gives clear sound quality. |
|
| 10-1 Specifications | |
|
Microphone Pattern Weight Impedance Sensitivity S/N Ratio Max Input Working Voltage Current Consumption Frequency Response Color Plug Accessories Battery |
Electret Condenser Unidirectional 38 grams (without plug) 2K ohms -63 db (+ -4db) nt I KHZ More than 30db 120db SPL 1 .5V ( 1 V - 1 0V) 0.4MA Max at 1.5V 150-lOKHZ Matte Black Finish 1/4 plug (3 ft. cord) Wind Sock 1.5V button cell |
| 10-2 Specifications | |
|
Microphone Pattern Frequency Response Impedance Sensitivity S/N Ratio Max Input Weight Color Plug Accessories |
Dynamic Noise Cancelling Unidirectional 150-1 OKHZ 200 ohms (+ -20%) -83 db (+ -4db) at 1 KHZ More than 30db 120db SPL 43 Grams(without plug) Matte Black Finish 1/4" plug (3 ft. cord) Wind Sock |
|
10-90 ULTRA-MINIATURE TIE CLASP MICROPHONE 9/32" diameter by 3/4" length. Extremely wide frequency range permits compatibility in all instrumental broadcast and recording fields. Tie clasp grip permits freedom of hands. Complete with carrying case, battery and 20 ft. cable with 1/4" phone plug. |
|
| Specifications | |
|
Type Impedance Frequency Response Sensitivity Signal Noise Ratio Sound Pressure Level Polar Pattern Cable Power Supply Battery Life |
Electret Condenser Mike 600 ohms at 1,000 Hz 50 to 16,000 Hz -64 dB +/- 3dB at 1,000 Hz 50 dB at 1,000 Hz Max. 130 dB Omni-directional 6M (20 ft.) 1-Conductor Shielded 1.35V Button Cell 2,000 hrs. in cont. operation |
|
10-91 MINIATURE TIE CLASP MICROPHONE Extra small, only 3/8" diameter. Excellent voice quality makes this new tie clasp microphone most versatile. Great for interviews, P.A., radio and T.V. network use, where free use of hands is necessary. Complete with battery, wind screen, tie clip, 3.5 mm plug. 10 ft. cord. |
|
| Specifications | |
|
Type Frequency Response Sensitivity Length Impedance Package Power Supply Polar Pattern |
Electret Condensor Microphone 50 Hz-8 kHz -60 dB +/- 3 dB 1 1/4" 600 ohms at 1,000 Hz Blister (Hanger Type) 1.5V Button Cell Omni-Directional |
|
10-11 MINIATURE ELECTRET CONDENSER MICROPHONE Designed for all microphone uses. Excellent quality at a low cost for voice, public address and vocal. 6 ft. cable is terminated with a right angle 3.5 mm plug. ON/OFF switch on clip. |
|
| Specifications | |
|
Type Frequency Response Sensitivity Polar Pattern Impedance Power Supply Accessories |
Electret Condenser 50-18 kHz -65db (0db=1v/u bar) Omni-directional 600 Ohms 1.5 volt Button Cell Battery, Tie Clasp, Wind Screen |
|
10-12 MINIATURE ELECTRET CONDENSER MICROPHONE This microphone is designed for all uses. ON/OFF switch enclosed on the beltclip for easy use. Designed for quality at a low cost. 6 ft. cable is terminated with a 3.5 mm plug. |
|
| Specifications | |
|
Type Frequency Response Sensitivity Polar Pattern Impedance Power Supply Accessories |
Electret Condenser 50-18Khz -65 db at 1,000Hz Omni-Directional 1KOhm(=/-30% at 1 khz) 1.5 volt AAA battery 3.5mm to 1/4" adapter, Battery, Tie Clasp, Wind Screen |
|
10-20 DUAL IMPEDANCE DYNAMIC MICROPHONE Features a uni-directional element, built-in pop, noise filter and a 20 ft. cable (with holder). |
|
| Specifications | |
|
Frequency Response Cable end Sensitivity Sensitivity |
80-12 kHz 1/4" Phone plug 50K ohm-60 dB +/- 3 dB at 1kHz 500 ohm-77 dB +/- 3 dB |
|
10-22 ECONOMY DYNAMIC MICROPHONE This uni-directional dynamic microphone has an 10 ft. cable and 1/4" phone plug. A wind screen is built into the wire mesh ball head to prevent hiss, pop and wind noise.noise. |
|
| Specifications | |
|
Impedance Frequency Response Sensitivity |
500 ohm 80-12 kHz -77 dB +/- 3 dB at 1 kHz |
|
10-25 UNIVERSAL REMOTE CONTROL MICROPHONE Specially designed for transistor recorders. Remote on/off switch with two individual pin plugs (2.5 mm and 3.5 mm). May be used as dual plug for remote control recording for cassette, reel type recorders or single plug for general microphone use. May be hand held or used with desk holder supplied. Impedance 50K ohms. Frequency response, 60-12,000 Hz. |
|
10-29 CASSETTE TYPE MICROPHONE Universal microphone for use with most cassette recorders. 200 ohm low impedance type, with stand, two individual pin plugs (2.5 mm and 3.5 mm), and on/off switch. |
|
10-27 UNIVERSAL DYNAMIC MICROPHONE Universal microphone for use with most cassette recorders. 200 ohm low impedance type, with stand, on/off switch and 3.5 mm plugs. |
|
| Specifications | |
|
Sensitivity Frequency Response |
-80 db 100-10 KHz, Uni-Directional |
|
10-38B DESK TOP MICROPHONE This dynamic desktop paging microphone is ideal for most communication needs. Its push-to-talk switch, locking mode and omnidirectional microphone element make it maintenance-free. Comes with 15 ft. Iong, 3-conductor plus shield cord (Low Z) terminated with 1/4" phone plug. 6 inch gooseneck. |
|
10-80 LOW IMPEDANCE OMNIDIRECTIONAL MICROPHONE Low impedance, 500 ohm with 5 ft. retractable cable terminated with 3 wires plus shield. Push-to-talk switching. Excellent with CB, ham and general communications use. Individually packaged. |
|
| Specifications | |
|
Frequency Response Color |
300 Hz-5 kHz Black |
|
10-81 OMNIDIRECTIONAL DYNAMIC MICROPHONE 500 ohm hand-held microphone features a 6 ft. retractable cable terminated with 3 wires plus shield. Push-to-talk switch. |
|
| Specifications | |
|
Frequency Response Sensitivity |
200 Hz-5 kHz -75 dB +/- 4 dB at 1 kHz re lv/uBar |
|
DUAL IMPEDANCE MATCHING LINE TRANSFORMERS Permits use of low impedance microphone into a high impedance input. No wiring necessary. |
|||||||
|
10-76 1/4" Male phone plug to XLR Female. 500 Ohm Input, 50K Ohm Output. |
10-77 1/4" Female phone jack to 1/4" phone plug, w/6" cable. 600 Ohm Input, 50K Ohm Output. |
10-79 XLR Male to 1/4" Male phone plug. 600 Ohm Input, 50K Ohm Output. |
10-86 XLR male to 1/4" phone plug; hi/low switch and 6" cable. 600 Ohm input, 50K Ohm |
10-87 XLR Female to 1/4" Female phone jack. 600 Ohm Input, 50K Ohm Output. |
10-88 XLR male to XLR Female. 600 Ohm Input, 50K Ohm Output. |
10-89 1/4" phone jack to XLR male plug. 500 Ohm Input, 50K Ohm Output. |
10-99 XLR Female to 1/4" male phone plug, w/9" cable. 600 Ohm Input, 50K Ohm Output. |
|
MULTI-COLOR WINDSCREEN SETS Decorative, multiple color, special soft foam provides quick and easy identification, avoiding mixups. Blocks out hiss, pop, and wind noise (packaged for display racks). |
||||
|
10-9 23/4" High Screen Universal Type- Fits slim models from 3/4" to I 1 1/8". (1 per pkg.). |
10-53 Wind screen for a 13/4" to 2" diameter microphones . (sennheiser style) 1 per pkg. |
10-67 2 1/2" high wind screens to fit 1 3/8" to 13/4" diameter microphones, available in Red, Green Yellow, Black. 1 per pkg., specify color. |
10-68 Wind screens for spherical head microphone 1 5/8" High to fit over 13/4" to 2" microphones. Available in Red, Orange Yellow, Green, Black. 1 per pkg., specify color. |
10-69 Contains four 7/8" High screens to fit 1/4" to 1/2" microphone. Designed to fit lavalier type microphones . 1 each Red, Black, Yellow, Green. |
|
ELECTRET CONDENSER MICROPHONE ELEMENTS Miniature in size, excellent quality. Working voltage range from 2-10 Vdc. Has many uses such as general replacement, recording devices, surveillance work, etc. |
|
|
10-83 (3/8" dia.) 10-84 (3/8" dia.) |
2 pin, P.C. Mt. + Case Tab. 3 pin, P.C. Mt. + Case Tab. (Balanced line type) |
|
10-41 MICROPHONE ELEMENT 1 " dia. ceramic element. |
|
|
Frequency response Sensitivity |
70-8000 cps. 54 dB-hi imp. |
|
10-49 MICROPHONE ELEMENT 15/16" dia., Hi-quality dynamic element, Ferrite magnet. |
|
|
Impedance Frequency Response |
500 ohm. 50-15,000 cps. |
|
10-95 20 ft. PROFESSIONAL MICROPHONE EXTENSION CABLE Male and female XLR connectors, low loss heavy gauge rubber cable. |
|
10-45 20 ft. MICROPHONE CABLE To fit 7/32" dia. microphones. Professional Series, 3-wire balanced line with Female XLR type connector on one end, 1/4" male mono plug on the other end. |
|
10-96 20 ft. PROFESSIONAL MICROPHONE EXTENSION CABLE Female XLR connector on both ends, low loss heavy gauge rubber cable. |
|
Female Xlr to 3.5mm Mono plug 6'. |
Female Xlr to 3.5mm Stereo plug. 6'. |
Female Xlr to 3.5mm Stereo plug 1'. |
Female Xlr to right angle 3.5mm Stereo plug 1' (Wired Pin 1 & 3 to Ground / Pin 2 hot). |
|
Male XLR to 3.5mm mono plug, 6'. (Wired Pin 1 & 3 to Ground / Pin 2 hot). |
Male XLR to 3.5mm Stereo plug, 6'. (Wired Pin 1 & 3 to Ground / Pin 2 hot). |
Female XLR to 1/4" Stereo plug 3'. (Wired Pin 1 - ground / pin2 Tip / pin3 Ring). |
Female XLR to 1/4" Stereo plug 6'. (Wired Pin 1 - ground / pin2 Tip / pin3 Ring). |
|
Female XLR to 1/4" Stereo plug 10'. (Wired Pin 1 - ground / pin2 Tip / pin3 Ring). |
Female XLR to 1/4" Stereo plug 10'. (Wired Pin 1 - ground / pin2 Tip / pin3 Ring). |
Male XLR to 1/4" Stereo plug 3'. (Wired Pin 1 & 3 to Ground / Pin 2 hot). |
Male XLR to 1/4" Stereo plug 6'. (Wired Pin 1 & 3 to Ground / Pin 2 hot). |
|
Male XLR to 1/4" Stereo plug 10'. (Wired Pin 1 & 3 to Ground / Pin 2 hot). |
Male XLR to 1/4" Stereo plug 15'. (Wired Pin 1 & 3 to Ground / Pin 2 hot). |
XLR "Y" cable one Male to two Females . Wired pin to pin |
XLR "Y" cable one Female to two Males . Wired pin to pin |
|
XLR "Y" to two 3 - pin XLR Females to a 3.5mm stereo plug. 6'.(Wired Pin 1 - ground / pin2 Tip / pin3 Ring). XLR's wired pin to pin. |
1' "Y" Cable, one Female XLR to two RCA Male plugs. Uses flat style cable. Wired: pin 1 ground both RCA's/ pin 2 tip (Hot) RCA #1 plug pin 3 tip (Hot) RCA #2. |
1' "Y" Cable, one Female XLR to two RCA Female plugs. Uses flat style cable. Wired: pin 1 ground both RCA's/ pin 2 tip (Hot) RCA #1 plug pin 3 tip (Hot) RCA #2. |
1' "Y" Cable, one Male XLR to two RCA Male plugs. Uses flat style cable. Wired: pin 1 ground both RCA's/ pin 2 tip (Hot) RCA #1 plug pin 3 tip (Hot) RCA #2. |
|
1' "Y" Cable, one Female XLR to two RCA Male plugs. Uses flat style cable. Wired: pin 1 ground both RCA's/ pin 2 tip (Hot) RCA #1 plug pin 3 tip (Hot) RCA #2. |
1' "Y" Cable 3.5mm Stereo right angle plug to two XLR female inline jacks. Wired: #1, 2 XLR Pins 1 & 3 to Ground (Sleve of 3.5mm plug) / pins 2 of XLR 1, 2 to (Hot) / tip of 3.5mm plug. Uses flat style cable |
6' "Y" Cable 3.5mm Stereo straight plug to two XLR Male inline jacks. Wired: #1, 2 XLR Pins 1 & 3 to Ground (Sleve of 3.5mm plug) / pins 2 of XLR 1, 2 to (Hot) / tip of 3.5mm plug. Uses flat style cable |
|
|
10-50 MICROPHONE RETRACTABLE COIL CHORD Excellent for CB, Ham or general replacement use. 3 conductors plus 1 shield. |
|
10-97 MICROPHONE CLIP HOLDERS (Tie Clip) To fit 7/32" dia. microphones. |
|
10-32 MICROPHONE STAND Polished chrome plated or black finish stem with 3/8" - 16 thread connector and a detachable 5/8" - 27 screw adapter for microphone holder. 2 leg base with tubular legs. Legs braced with non-skid rubber tips. Weight: 5 Ibs. Height:collapsed - 35", extended - 64". |
|
10-31 MICROPHONE STAND Polished chrome plated or black finish with round black base. |
|
10-33 MICROPHONE STAND Polished chrome plated or black finish stem with 3/8" - 16 thread connector and a detachable 5/8" - 27 screw adapter for microphone holder. Heavy duty, compact, extra high elevation adjustment. 3 leg base with foldable tubular legs. Boom sets accessories included with stand for greater adjustment and versatility. Weight: 7 Ibs., Height: collapsed - 33", extended - 63". |
|
MICROPHONE GOOSENECKS 5/8" - 27 connecting thread male to female on ends. |
|
|
10-36-6 10-36-13 10-36-19 |
6 inches 13 inches 19 inches |
|
10-S9 MICROPHONE ATTACHMENT Fits any floor stand with 5/8" 27 top end thread. Accepts two-microphone holder with 5/8" - 27 connecting thread. |
|
10-34 GOOSENECK BASE Surface mounting, die cast base, fits most gooseneck types with 5/8" threads. Base has MALE threads. |
|
10-35 GOOSENECK BASE Surface mounting, die cast base, fits most gooseneck types with 5/8" threads. Base has FEMALE threads. |
|
10-54 DESK MICROPHONE STAND Mike stand with 5/8" x 27" thread. Black metal base 4" dia., rod is 3" from top of base. Individual box. |
|
10-55 DESK MICROPHONE STAND A beautiful modernistic desk stand. "U" shaped base finished in black. Supplied with a polished chrome upright tube, threaded 5/8-27 at both ends. Can be used with the other mike accessories. |
|
10-112 PATCH BAY Our professional audio series continues with this 32 point patch bay. The 10-112 combines high quality construction and optimum insertion of either BNC or RCA type plugs {specify which when ordering). Its combination of aluminum and steel construction makes the 10-112 ideal for rack mounting in the toughest environments. The 10-112 comes with 32 labeled & isolated patch points. (RCA or BNC) 10-112-BNC for BNC version. Specifications: Dimensions: 19" x 1 1/2 " x 11 1/16". |
|
10-72 PRE-AMP Our low-noise, 100% shielded pre-amp will provide total control over many conflicting audio situations. It features adjustable gain as well as high & low frequency adjustments. It accepts low & high frequency impedance signals, and has a 3-way power source for clean audio reproduction. |
|
| Specifications | |
|
3-way power supply Current Drain Input Impedance Output Impedance High Adj Low Adj Input - 0utput Adjustable Gain Control Power Switch Signal to Noise |
9V Battery 6-12V DC Adapter 45-756 (Not included) 25MA 5K 600 Ohm +10 Db @ 10kHz +/- 10Db @ 250Hz XLR Type Connectors + 10 db Rocker w/LED Indicator -70 Db |
|
10-73 5-CHANNEL PORTABLE STEREO MIXER Professional sound quality. Compact in size, puts you in full control at all times. So versatile, handles ail low impedance microphones, including high impedance up to 1 megohm. Individual channels can be operated separately or may be tied together in any sequence necessary with or without the use of the master volume control. |
|
10-111 DIRECT BOX Features: Single toggle switching for selecting either pick-up or amplifier setting. Feeds signal from your instrument or amplifier to a recording console or P.A. system. Hi "Z" output allows you to feed signal to your amp or speaker system for live monitoring. Also functions as a Bi-directional transformer, to change from Hi Z to Low Z or Low Z to Hi Z Variable Filter with ground lift capabilities. |
|
| Specifications | |
|
Input Impedance Dimensions Line output impedance Frequency Fixed pod |
200K 4 3/4" X 3 1/8" x 1 5/8" 1 K ohm 20-20K 30 dB |
|
10-1 13 MICROPHONE SPLITTER Splits input of a single microphone to two different outputs, both input and output signals may be used to provide separate isolated feeds to both a house and monitor system, P.A. recording system or similar application where double outputs are required. |
|
| Specifications | |
|
Input Impedance Dimensions Output impedance Frequency Response |
600 ohm 4 3/4" X 3 1/8" x 1 5/8" 600 ohm 20-20K |
|
80-575 STEREO UNIVERSAL PREAMP Line preamp, mic preamp, phono preamp, headphone preamp. Select from 4 or more standard configurations - specify which configuration when ordering. A few components are easily changed on the PC board for each preamp. The unit is available in a chassis, or completed circuit board with labeled black face plate. Includes DC power adapter. |
|
| Specifications | |
|
Input/Output Jacks Power Input Impedence 0utput Impedence Gain Frequency Response |
RCA Type 9VDC, 2.5mm Coax Jack Factory Adjusted 5K, Factory Adjusted Adjustable 20Hz-20Khz, +-3db |
|
|
Return to table of contents
You are visitor # to
visit this page.